Book

 

This post below about How to Install a Bathtub Yourself is rather interesting. Check it out for yourself and see what you think of it.

Setting up a bathtub isn't exactly rocket science, yet it does need strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the project can relocate speedily; if you have to open up a wall surface to eliminate the old bathtub and position the new tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and set in the new one. See to it you have qualified on your own for the task and also are comfortable attempting it. Rather than employing a professional to take over a halfway-completed task, it is far better to think about using one before you start. Possibilities are you might require a specialist plumber to make tube links.
This post will certainly aid you mount a new tub in your bathroom if you have already bought a new tub as well as do not require to transform the arrangement of your previous water pipes.
Your devices and also material list must comprise the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is detach the supply of water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be rather problematic due to the limited access that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.

 

 

Suitable New Taps

If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Safeguard the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former type ought to be linked to the tap ends initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Setting up the Bathtub

Making use of both wooden boards under its feet, position the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub until the spirit level reads degree.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water and also check all joints and brand-new pipework for leakages and tighten them if required. Fill the bath tub as well as also check the overflow outlet and the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the maker's user's manual. Tiling and securing around the tub must wait up until the bathtub has actually been used at least when as this will certainly resolve it into its last placement.

 

 

Preparing for the Installment

To start with, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final position.

 

 

Tiling Around the Tub

In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall between the bathroom and also the tiling, causing problems with dampness and also possible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water before securing, to enable the activity experienced when the tub is in use. The sealer can crack fairly early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the market. It is advisable to fit the tiles making use of water-resistant or water-proof glue as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I was shown that editorial on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an acquaintance on our other domain. Are you aware of somebody else who is looking into the topic? Please feel free to promote it. Thanks for going through it.

Trusted by locals for emergencies.